Unmanned technologies globally
jDrones documentation wiki

User Tools

Site Tools


can:gennode21-definition

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
can:gennode21-definition [2018/11/21 20:08]
olliw version small
can:gennode21-definition [2018/11/22 00:08] (current)
olliw
Line 1: Line 1:
 ===== Gen.Node v2.1-jD ===== ===== Gen.Node v2.1-jD =====
  
-This is jDrones version of UC4H Generic ​Node. Documentation is accurate only if you are using original jDrones Gen.Node boards. ​+This is jDrones version of the UC4H General-Purpose ​Node. Documentation is accurate only if you are using original jDrones Gen.Node boards. ​
  
  
Line 9: Line 9:
 ==== Board Definitions ==== ==== Board Definitions ====
  
-TOP Side of the UC4H Gen.Node ​v2.1+Top side of the UC4H Gen.Node ​board with pin definitions.
  
 {{:​can:​jdrones_gennode21_generic.jpg?​nolink|}} {{:​can:​jdrones_gennode21_generic.jpg?​nolink|}}
Line 20: Line 20:
  
 ^ Connector ​     ^ Description ​      ​^ ​ ^ Connector ​     ^ Description ​      ​^ ​
-| EXT5    | External 5V input if you need more power than what C5V line can provide| +| CAN1    | UAVCAN main connector. Identical to CAN2 port, can be used for linking to another UAVCAN device or terminator.
-| E5O     | Output pin for EXT5 connector. Used for external 5V is needed | +| CAN2    | UAVCAN main connector. Identical to CAN1 port, can be used for linking to another UAVCAN device or terminator.
-| CAN1    | UAVCAN main connector. Identical to CAN2 port, can be used for linking to another UAVCAN device or terminator| +| C5V     | C5V is connected to CAN1/2 power line and protected with 500mA automatic ​fuse. | 
-| CAN2    | UAVCAN main connector. Identical to CAN1 port, can be used for linking to another UAVCAN device or terminator| +| 3V3     | 3.3V LDO regulated output pin. Same LDO provides power to the main MCU. Max output ​3.3V/300mA. | 
-| C5V     | C5V is connected to CAN1/2 power line and protected with 500mA automatic ​FUSE. | +| C2      | C2 / Tx1  | 
-| 3V3     | 3.3V LDO regulated output pin. Same LDO provides power to the main MCU. Max output ​3V3/300mA. | +| C1      | C1 / Rx1  | 
-| C2      | C2 / Tx1 | +| B2      | B2 / Tx2 / TLM  | 
-| C1      | C1 / Rx1 | +| B1      | B1 / Rx2  | 
-| B2      | B2 / Tx2 / TLM | +| A2      | A2 / SCL  
-| B1      | B1 / Rx2 | +| A1      | A1 / SDA  
-| A2      | A2 / SCL,      ​+| GND     | Common ground, used to ground your additional hardware. | 
-| A1      | A1 / SDA,      ​+| EXT5    | External 5V input if you need more power than what the C5V line can provide. | 
-| GND     | Common ground, used to ground your additional hardware |+| E5O     | Output pin for EXT5 connector. Used for external 5V if needed. ​|
  
  
Line 41: Line 41:
 ==== Firmwares ==== ==== Firmwares ====
  
-There are TWO main softwares for this board. One is Bootloader ​and another is operation ​Firmware. Please do not mix them. Firmwares ​you upload with SLCAN board over the UAVCAN databus. ​Bootloader ​is uploaded via SWD connector. ​+There are //​**two**// ​main softwares for this board. One is the bootloader ​and another is the operation ​firmware. Please do not mix them. The firmware ​you upload with the SLCAN board over the UAVCAN databus. ​The bootloader ​is uploaded via the SWD connector. ​
  
-This board is coming with latest UC4H Bootloader ​firmware ​uploaded at jDrones. ​ +This board is coming with the latest UC4H Bootloader uploaded at jDrones. Normally you do not need to upload it unless ​you want to upgrade ​it or have "​bricked"​ your UC4H board. You need a [[can:​stm32prg|jDrones STM32 Programmer]] for burning the bootloader into this board. ​
-Normally you do not need to update bootloader ​unless: You want to upgrade or you have "​bricked"​ your UC4H board. ​+
  
-You can download ​always latest ​firmwares ​and bootloaders ​from our document site. You need jDrones STM32 Programmer to burn bootloader in this board+You can always ​download the latest ​firmware ​and bootloader ​from our document site.
  
-Firmwares/​Bootloaders,​ please take a look at our [[can:​firmwares|firmware page]]+Firmwares/​Bootloaders,​ please take a look at our [[can:​firmwares|firmware page]].
  
  
can/gennode21-definition.1542830922.txt.gz · Last modified: 2018/11/21 20:08 by olliw