User Tools
can:slcan
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
can:slcan [2018/11/18 04:05] admin |
can:slcan [2018/11/19 20:44] (current) olliw spelling |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | Coming right up. | ||
| - | |||
| - | In meanwhile, please take a look at [[http://olliw.eu/2017/uavcan-for-hobbyists/]] | ||
| - | |||
| - | ---- | ||
| - | |||
| ====== SLCAN Board ====== | ====== SLCAN Board ====== | ||
| + | {{ :can:jdrones_uavcan_slcan_v11.jpg?nolink&400|}} | ||
| - | === Board definition === | + | * [[can:slcan-definition|SLCAN Board]] - Definition of SLCAN board |
| + | * [[can:slcan-using|Using SLCAN]] - Connecting and using SLCAN board | ||
| + | * [[can:slcan-fwupdate| Firmware]] - How to update firmware | ||
| - | Picture of SLCAN board with quick definitions. Look below to more detailed definitions of the board. | + | * [[http://store.jdrones.com/uc4g_slcan_v11_p/uc4hslcan11.htm|jDrones Store]] - Where to get one |
| + | |||
| + | This board is part of the //UC4H// UAVCAN family. | ||
| - | {{:can:jdrones_slcan_generic.jpg?nolink&600|}} | + | SLCAN boards are jointly created with OlliW. You can follow Olli's work at [[http://olliw.eu/2017/uavcan-for-hobbyists/|olliw.eu]] |
| - | + | ||
| - | To connect on your UAVCAN bus, you need SLCAN adapter and software to read UAVCAN messages. Pavel K. who is original author of UAVCAN has greated a great software for UAVCAN operations. | + | |
| - | + | ||
| - | Download UAVCAN GUI from here: https://uavcan.org/GUI_Tool/Overview/ | + | |
| - | + | ||
| - | === Connection definitions === | ||
| - | ^ Connector ^ Description ^ | ||
| - | | USB | USB connection to your computer. This serial port USB uses Silabs CP2102 Serial adapter. Make sure that you always have latest drivers installed for CP2102. \\ \\ You can download latest drivers from [[https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers|Silabs website]] | | ||
| - | | UART2 | UART port from MCU, used only for debugging needs and using this port needs custom firmware to be activated. Normally not in use | | ||
| - | | SWD | Onboard STM32 programming port. Connector pitch is 1.27mm. This port is used to program SLCAN firmware on the board. Best to use jD-STM32 Programmer + 1.27mm pogopin adapter board to program SLCAN board. You can get jD-STM32 Programmer from [[http://store.jdrones.com/jdrones_stm32_programmer_p/jdstm32prg10.htm|jDrones Store]]. \\ \\ Pin order from left to right: //GND, SWCLK, SWDIO, 3v3// \\ \\ __**BEWARE** Always check orientation of the programmer.__ This port is not reverse polarity protected. | | ||
can/slcan.1542513934.txt.gz · Last modified: 2018/11/18 04:05 by admin
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial 4.0 International
