This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
can:gennode21-definition [2018/11/18 09:14] admin |
can:gennode21-definition [2018/11/22 00:08] (current) olliw |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Gen.Node V2.1-jD ===== | + | ===== Gen.Node v2.1-jD ===== |
- | This is jDrones version of UC4H Generic Node. Documentation is accurate only if you are using original jDrones Gen.Node boards. | + | This is jDrones version of the UC4H General-Purpose Node. Documentation is accurate only if you are using original jDrones Gen.Node boards. |
Line 9: | Line 9: | ||
==== Board Definitions ==== | ==== Board Definitions ==== | ||
- | TOP Side of the UC4H Gen.Node v2.1 | + | Top side of the UC4H Gen.Node board with pin definitions. |
{{:can:jdrones_gennode21_generic.jpg?nolink|}} | {{:can:jdrones_gennode21_generic.jpg?nolink|}} | ||
Line 20: | Line 20: | ||
^ Connector ^ Description ^ | ^ Connector ^ Description ^ | ||
- | | EXT5 | External 5V input if you need more power than what C5V line can provide| | + | | CAN1 | UAVCAN main connector. Identical to CAN2 port, can be used for linking to another UAVCAN device or terminator.| |
- | | E5O | Output pin for EXT5 connector. Used for external 5V is needed | | + | | CAN2 | UAVCAN main connector. Identical to CAN1 port, can be used for linking to another UAVCAN device or terminator.| |
- | | CAN1 | UAVCAN main connector. Identical to CAN2 port, can be used for linking to another UAVCAN device or terminator| | + | | C5V | C5V is connected to CAN1/2 power line and protected with a 500mA automatic fuse. | |
- | | CAN2 | UAVCAN main connector. Identical to CAN1 port, can be used for linking to another UAVCAN device or terminator| | + | | 3V3 | 3.3V LDO regulated output pin. Same LDO provides power to the main MCU. Max output 3.3V/300mA. | |
- | | C5V | C5V is connected to CAN1/2 power line and protected with 500mA automatic FUSE. | | + | | C2 | C2 / Tx1 | |
- | | 3V3 | 3.3V LDO regulated output pin. Same LDO provides power to the main MCU. Max output 3V3/300mA. | | + | | C1 | C1 / Rx1 | |
- | | C2 | C2 / Tx1, | | + | | B2 | B2 / Tx2 / TLM | |
- | | C1 | C1 / Rx1, | | + | | B1 | B1 / Rx2 | |
- | | B2 | B2 / Tx2 / TLM, | | + | | A2 | A2 / SCL | |
- | | B1 | B1 / Rx2, | | + | | A1 | A1 / SDA | |
- | | A2 | A2 / SCL, | | + | | GND | Common ground, used to ground your additional hardware. | |
- | | A1 | A1 / SDA, | | + | | EXT5 | External 5V input if you need more power than what the C5V line can provide. | |
- | | GND | Common ground, used to ground your additional hardware | | + | | E5O | Output pin for EXT5 connector. Used for external 5V if needed. | |
Line 41: | Line 41: | ||
==== Firmwares ==== | ==== Firmwares ==== | ||
- | There are TWO main softwares for this board. One is Bootloader and another is operation Firmware. Please do not mix them. Firmwares you upload with SLCAN board over the UAVCAN databus. Bootloader is uploaded via SWD connector. | + | There are //**two**// main softwares for this board. One is the bootloader and another is the operation firmware. Please do not mix them. The firmware you upload with the SLCAN board over the UAVCAN databus. The bootloader is uploaded via the SWD connector. |
- | This board is coming with latest UC4H Bootloader firmware uploaded at jDrones. | + | This board is coming with the latest UC4H Bootloader uploaded at jDrones. Normally you do not need to upload it unless you want to upgrade it or have "bricked" your UC4H board. You need a [[can:stm32prg|jDrones STM32 Programmer]] for burning the bootloader into this board. |
- | Normally you do not need to update bootloader unless: You want to upgrade or you have "bricked" your UC4H board. | + | |
- | You can download always latest firmwares and bootloaders from our document site. You need jDrones STM32 Programmer to burn bootloader in this board. | + | You can always download the latest firmware and bootloader from our document site. |
- | Firmwares/Bootloaders, please take a look at our [[can:firmwares|firmware page]] | + | Firmwares/Bootloaders, please take a look at our [[can:firmwares|firmware page]]. |